Jm GC-24T Assembly Manuale Utente

J. & M. Mfg. Co., Inc.P.O. Box 547 Ft. Recovery, OH 45846Ph: (419) 375-2376 Fax: (419) 375-2708www.jm-inc.comMODEL GC24t-1 GRAIN CART ASSEMBLY RE

GC24t-1 Grain Cart assembly-10- STEP - 18 STEP -17Attach the front OAS middle panel. Remove the two temporary bolts. Use (17) M10 x 25MM serrated hex

GC24t-1 Grain Cart assembly-11- STEP - 20 STEP - 19Rear OAS Middle PanelRear AS Middle PanelAttach the rear OAS lower middle panel. Remove the two tem

GC24t-1 Grain Cart assembly-12- STEP - 22 STEP - 21Rear AS Upper Middle PanelRear OAS Upper Middle PanelAttach the rear AS upper middle panel. Use (18

GC24t-1 Grain Cart assembly-13- STEP - 23 STEP - 24OAS Front Bottom PanelAS Front Bottom PanelAttach the OAS front bottom panel. Use (16) M10 x 25MM s

GC24t-1 Grain Cart assembly-14- STEP - 26 STEP - 25OAS Rear Bottom PanelAs Rear Bottom PanelOAS Rear Middle PanelAttach the OAS rear bottom panel. Use

GC24t-1 Grain Cart assembly-15- STEP - 28 STEP - 27OAS Center Middle PanelOAS Front Middle PanelAttach the OAS center middle panel. Use (18) M10 x 25M

GC24t-1 Grain Cart assembly-16- STEP - 30 STEP - 29AS Rear Middle PanelAS Center Middle PanelAttach the AS rear middle panel. Use (17) M10 x 25MM serr

GC24t-1 Grain Cart assembly-17- STEP - 32 STEP - 31Attach the clean out door mount using (2) M10 x 25MM serrated ange hex head bolts and (2) M10 serr

GC24t-1 Grain Cart assembly-18- STEP - 33 STEP - 34STOP! Tighten the bolts that are surrounded by the box in the above gure. These bolts will be inac

GC24t-1 Grain Cart assembly-19- STEP - 36 STEP - 35Using an overhead hoist, lift the bottom tube assembly using the lifting hook holes. This should he

GC24t-1 Grain Cart assembly-2- For stability set the axle weldment up on blocks using an overhead hoist and chain. The blue sticker or tack welds on t

GC24t-1 Grain Cart assembly-20- STEP - 38 STEP - 37Attach the rear AS top panel. Use (9) M10 x 25MM serrated hex head bolts to attach the rear AS top

GC24t-1 Grain Cart assembly-21- STEP - 40 STEP - 39Attach the AS front top panel. Use (15) M10 x 25MM serrated hex head bolts and (15) M10 serrated he

GC24t-1 Grain Cart assembly-22- STEP - 42 STEP - 41AS Top Rear PanelOAS Top Front PanelAttach the AS rear top panel. Use (16) M10 x 25MM serrated hex

GC24t-1 Grain Cart assembly-23- STEP - 44 STEP - 43OAS Top Middle PanelOAS Top Rear PanelAttach the OAS middle top panel. Use (8) M10 x 25MM serrated

GC24t-1 Grain Cart assembly-24- STEP - 46 STEP - 45Front AS Top PanelFront OAS Top PanelAttach the front AS top panel. Use (13) M10 x 25MM serrated he

GC24t-1 Grain Cart assembly-25- STEP - 48 STEP - 47Install the gearbox top plate. Use (10) M10 x 25MM serrated hex head bolts and (10) M10 serrated he

GC24t-1 Grain Cart assembly-26- STEP - 50 STEP - 49Install the {1} rear slope splice plate & the {2} side slope splice plate. Use (10) M10 x 25MM

GC24t-1 Grain Cart assembly-27- STEP - 52Install all four side gussets. Use (12) M10 x 25MM serrated hex head bolts and (12) M10 serrated hex ange nu

GC24t-1 Grain Cart assembly-28- STEP - 54 STEP - 53Install the opposite auger side and auger side slope braces. Use (6) M10 x 25MM serrated hex head b

GC24t-1 Grain Cart assembly-29- STEP - 56 STEP - 55Tank ScreenInstall the tank screen. Use (4) M10 x 25MM serrated hex head bolts and (4) M10 serrated

GC24t-1 Grain Cart assembly-3- STEP - 4 STEP - 3 Set the axle weldment up on blocks. Insert four digistar weigh bars. Use 1” x 6” bolts to attach we

-30- STEP - 57GC24t-1 Bolt toGether Grain CartInstall the front and rear cross braces. One set includes two braces which are 130” inches(330cm) in len

GC24t-1 Grain Cart assembly-31- STEP - 59 STEP - 58Install the front to back brace. Use (2) M12 x 25 MM serrated ange hex head bolts and (2) M12 ser-

GC24t-1 Grain Cart assembly-32- STEP - 61 STEP - 60Attach the high sideboard. Use (22) M10 x 25 MM serrated hex head bolts and (22) M10 serrated hex 

GC24t-1 Grain Cart assembly-33- STEP - 63 STEP - 62Attach the low side board. Use (23) M10 x 25 MM serrated hex head bolts and (23) M10 serrated hex 

GC24t-1 Grain Cart assembly-34-Attach the ear mount pads. Use (8) M16 x 45 MM and (8) M16 locking nuts to attach the ear mount pads to the front leg.

GC24t-1 Grain Cart assembly-35- STEP - 67 STEP - 66Install all three windows. The top window consists of the window and window seal. The front and rea

GC24t-1 Grain Cart assembly-36- STEP - 69 STEP - 68Install driveline shield. Use (3) M10 x 25MM serrated hex head bolts and (3) M10 serrated hex ange

GC24t-1 Grain Cart assembly-37- STEP - 70Install knuckle guard. Use (2) M10 serrated hex head bolts and (2) M10 serrated hex ange nuts to attach the

GC24t-1 Grain Cart assembly-38- STEP - 73 STEP - 72Install the auger top tube assembly and pivot pin with 1/2” x 1-1/2” bolts, extra large washers and

GC24t-1 Grain Cart assembly-39- STEP - 75 STEP - 74Install the bafe hinge. Use (6) M6 x 20MM bolts, locknuts, and washers.Use an overhead hoist and c

GC24t-1 Grain Cart assembly-4- STEP - 6 STEP - 5Place the front leg onto the main frame using an overhead hoist. Use a drift pin to help line up the h

GC24t-1 Grain Cart assembly-40- STEP - 77 STEP - 76Install the PTO slip clutch assembly. The PTO shaft will need to be shortened depending on the dist

GC24t-1 Grain Cart assembly-41- STEP - 78Install all of the rubber grommets. There is a small and a large size. Insert a rubber grommet where ever the

-42-GC24t-1 Grain Cart assemBly STEP - 80Install the wheels and tires with 3/4” lug nuts. Be sure to tighten and monitor lug nuts to make sure that th

GC24t-1 Grain Cart assembly-43- STEP - 2 STEP - 81Ground(White Wire)Field Light (Black Wire)Amber Flashing & Turn Signal (Green Wire)Amber Flashin

GC24t-1 Grain Cart assembly-44- STEP - 82Hitch Weldment1” x 7-1/2” Hex Bolt2-1/2” Hitch Spindle2-1/2” Sleeve3/4” x 3” Hex BoltHitch Plate Weldment1” C

-45- STEP - 82Feed the Weigh Bar wire through the left side of the A-frame, exit-ing out the grommet hole directly behind the front leg weldment.Use 3

GC24t-1 Grain Cart assembly-46- STEP - 83Junction BoxInsert all of the wires into the Junction Box according to the diagram above. Connect the wires t

GC24t-1 Grain Cart assembly-47- STEP - 85 STEP - 84Install two 1/4” x 29” (736.6mm) hy-draulic hoses for the shut off gate cyl-inder to the shell bulk

GC24t-1 Grain Cart assembly-48- STEP - 87 STEP - 86# Description1 1/2” X 1 1/2” Clevis pin w/ cotter pin2 1/4” St. elbow3 1/4” x 28’ (8534mm) Hydrauli

GC24t-1 Grain Cart assembly-49- STEP - 88 STEP - 8814”13”73”53.5”50.5”9.75”For the slider option the diverter valve will need to be installed. Bolt th

GC24t-1 Grain Cart assembly-5- STEP - 8 STEP - 7Attach the rear rail. Use (8) M10 serrated ange bolts to attach the rear rail to the rear leg. Attac

GC24t-1 Grain Cart assembly-50-Decal 1of 3 Measure 14” from seam. Start at rear end of Top AS Front Panel.14”StartMade in USA decal. Center in betwe

GC24t-1 Grain Cart assembly-51-Made in USA decal. Center in between decal 1 and top of AS rail. Start at edge of J&M decal then work to the right.

GC24t-1 Grain Cart assembly-52- STEP - 89(Top side of Top Tube)The remaining yellow stickers are to be placed in the four corners along the top edge o

GC24t-1 Grain Cart assembly-6- STEP - 10 STEP - 9Attach the opposite auger side rail (OAS). Use (4) M10 serrated ange nuts to attach the OAS to the

GC24t-1 Grain Cart assembly-7- STEP - 12 STEP - 11Measure from corner to corner on the rails. Reposition the front leg to get the measurements to be w

GC24t-1 Grain Cart assembly-8- STEP -14 STEP - 13Attach the rail corner auger piece. Use (2) M10 serrated ange hex head bolts and (2) M10 serrated he

GC24t-1 Grain Cart assembly-9- STEP -16 STEP - 15Attach the front lower panel. Use (2) temporary M10 serrated ange bolts to hold the front lower pane